1. Home
  2. Faux fur guides
  3. How to fix a faux fur…

Faux fur guides · 4 min read

How to fix a faux fur hood: clean it, repair it or replace it

Damaged faux fur hood

The hood is the first part of a coat to suffer, which is why so many people end up looking for how to fix a faux fur hood. It touches your hair and whatever products are in it, rubs against your collar and the back of seats, catches the rain, and often gets dried too close to a radiator.

Before you repair anything, you need to know what’s wrong with it. This guide runs through the five common types of damage, from the simplest to the most permanent, and tells you which ones you can sort out at home.

What damages a faux fur hood

Skin oils and hair products. The pile turns greasy, sticks together in clumps and goes grey. It’s the most common problem, and the easiest to deal with.

Friction. At the back of the neck and on the sides, the pile tangles and mats into clumps.

Crushing. A hood that’s been stored folded, or worn under a backpack, stays flat.

Heat. Drying it on a radiator or with a hairdryer on hot makes the fibre tips frizz and harden.

Stitching. A faux fur trim comes unstitched over time, or tears away at a press stud.

Greasy or sticky pile: clean the hood on its own

If the hood is detachable, take it off. Hand wash it in water no warmer than 30°C with a mild soap or a gentle shampoo. Rinse it in clean water, then press it in a towel without wringing.

Dry it in shape. A rolled-up towel slipped inside keeps it full. Leave it to dry flat, away from any heat, and brush it when the pile is almost dry.

If the hood is fixed, don’t soak the whole coat just for the hood. Whisk a little mild soap into lukewarm water and use only the foam on a cloth, one tuft at a time, in the direction of the pile. Rinse with a damp cloth, then dry the coat on a hanger with the hood up.

Matted or flattened pile: untangle it, then lift it

Matting comes out dry, with a soft-pin brush. Hold the base of each tuft between two fingers so you don’t pull on the backing fabric, then start at the tips and work down.

Flattened pile lifts with steam. Hang the hood in the bathroom while you have a hot shower, brush it lightly, then let it dry without touching it. The full method is in our guide on how to fluff up faux fur.

Melted pile: the damage you can’t repair

A synthetic fibre that’s been overheated stays curled and hard. If the patch is small, snip off the damaged tips with scissors, matching the length of the pile around them, and the difference disappears into the rest of the pile. If the whole trim has melted, replacing it is the only option.

Unstitched trim: sew it back by hand

You don’t need a sewing machine to put a faux fur trim back on. A fine needle and strong polyester thread in the colour of the backing will do.

Part the pile on each side of the seam with the point of the needle, so you only sew through the backing fabric.

Use small, tight stitches, overlapping 2 or 3cm of intact seam at each end.

Pick out any fibres caught in the seam with the point of a pin. The seam disappears under the pile.

Avoid fabric glue. It stiffens the backing, shows through short pile and gives way as the hood moves.

Replacing the hood

When the pile is worn down to the backing fabric, or melted over a large area, there’s nothing left to repair.

A detachable hood can be swapped for another one, as long as it uses the same fastening, either a zip or press studs.

A fixed hood can be covered with a hooded scarf. That’s a faux fur hood with two long scarf ends, which you wear over any coat and which keeps the back of your neck warm.

See the full range of faux fur scarves and hooded scarves. If you’re choosing a new hooded coat, our guide to the three types of hood will help.

FAQs

Can you machine wash a faux fur hood?
If it’s detachable and the label allows it, yes: at 30°C maximum, in a mesh bag, on a low spin. If it’s fixed, clean it by hand without soaking the coat.

How do you dry a hood without flattening it?
Lay it flat, stuffed with a rolled-up towel, away from radiators. Brush it when the pile is almost dry.

How do you fluff up a flattened faux fur hood?
Give it the steam from a hot shower, brush it lightly against the pile, then let it dry without touching it.

Can you glue a faux fur trim back on?
It’s best not to. Glue stiffens the backing fabric and gives way as the hood moves. Small hand stitches hold better and don’t show.

How do you stop a hood getting damaged?
Store the coat hanging up, with the hood unfolded. Never dry it on a radiator. And clean it once a season, before it gets greasy.

Further reading

Care guides: how to wash faux fur and faux fur shedding.

Find hooded styles in our women’s and men’s faux fur coats.

Read next